• Mini Keg Micro Regulator

click on thumbnail to zoom
Item #: Z78
Our Price: $44.99
We are currently out of stock. Enter your email below to receive a back in stock notice.
Email me when this is available 
  74 Gram Brewer's Edge® CO2 Cartridge (No Air Shipment) (+ $9.99)
  16 Gram Threaded CO2 For Beer (No Air Shipment) (+ $1.69)


The Brewer's Edge® Micro Regulator combines the precision of a Mini Regulator, with the portability of a simple gas injector. Featuring a 0-27 PSI range, precisely adjustable with the calibrated top knob. Best of all, it takes all standard 16 gram threaded and 74 gram threaded C02 cartridges, so you have the choice of a lightweight compact unit with the 16 gram, or a high capacity unit with the 74 gram cartridge. 

With this 0-27 PSI model, you can both dispense and force carbonate. Fits ball-lock kegs and only weighs  ounces. This model is angled so it clears KegLand Mini Kegs.

The flared outlet on the side that goes to the stainless ball lock fitting can be unscrewed and leaves a 1/8" female NPT port. Into this port you can screw any 1/8" NPT male thread hose barb or threaded outlet.

The regulator does not include a pictured cartridge, you will be offered a chance to order these when you put this in your cart. Note that C02 cartridges cannot be shipped by air or express, and cannot be shipped outside the lower 48 states due to aviation and postal regulations.

FOR C02 ONLY: This regulator is designed for use with C02 only, and should not be used with higher pressure argon or nitrogen gas.

Click to download the instructions in pdf format.


Average Rating:
(based on 1 review)

Showing 1 Review:

Review and Rate this Item
by Craig
on 8/6/2019
from Texas
Amateur fermentar of long duration
Handy little device that helps me with small (2.5 gal) keg.  The keg is difficult to seal - but with this device I can add pressure as needed.  In hind sight I would appreciate a gauge to know how much pressure I've got, but this is simple and easy to use.
Review and Rate this Item
1/2/2020 10:18:02 AM
I have 2.5 gal and 5 gal. kegland kegs. Will this micro regulator fit on the 5 gal kegs too?
Yes, it will fit any Ball Lock Keg.
4/3/2019 1:30:20 PM
Can I attach a pressure gauge to the regulator? I'll need less than 5 psi for dispensing.
No, the Micro Regulator does not have a port for a gauge. You might be able to use our item D62 Mini Regulator attached to our item I51 Gas Ball Lock Connector . You will also need a D87 Concave Washer to seal these two parts.
11/6/2018 12:42:10 PM
Hello! The micro regulator came with a Burst Disk Repair Kit, but there is nothing in the instructions on how to install it or when it would be needed. Can you provide directions on how this would be installed?Thanks!
Sorry for the confusion. Hold on to this kit, as you may never need it. If you ever find C02 leaking out the side holes of the screw that is stamped 1.8K, you will know your burst disk has failed. Unscrew this screw and install the white nylon disk and the copper burst disk in the same order as the ones in your regulator. That is all there is to it.
Steve K
10/28/2018 7:20:31 AM
Can you use the standard co2 regulators on these kegs also to dispense only, not force carb
Yes, you can use any regulator that has a gas hose and a female gas ball lock fitting on the end, as long as you have optional Ball Lock Lid P07.
Ask a Question

    Email A Friend

    Send this product to a friend...