• Keg Land Counterflow Wort Chiller

click on thumbnail to zoom
Item #: L21
Our Price: $54.99
In Stock, Will Ship On 05/26/2020.
  Chiller Tubing Kit For Counterflow (+ $24.99)


The best deal we have ever found in a highly efficient counterflow chiller! This 25' pure copper pipe unit features 3/8" hose barbs for both wort and chilling water, and is an extremely efficient chiller, capable of chilling 5 gallon batches in one pass, as long as your cooling water is 60° F. or less. Easier to clean than a plate chiller, and much more efficient than an immersion chiller. This can be pump or gravity fed. 

Connection tubing and fittings are not included: use 3/8” inner diameter vinyl (our item E04, sold per foot) for the cooling water and 3/8” inner diameter silicone tubing (our item J46) for the wort inlets and outlets. As this is a counterflow chiller, be sure to connect the cooling water inlet to the same end as the cooled wort outlet. 9¾” diameter, 10” tall.

If you need parts to convert your Robobrew or Mash & Boil to a 3/8" outlet barb so this tubing will fit the outlet, order one each of parts L86 nut, L11 Silicone O ring, and L83 3/8" hose barb. This assembled threaded hose barb will fit both the outlet of the Mash & Boil valve, as well as the outlet and upper pump outlet of the Robobrew.

See item Q96 if you need a complete hose connection kit for most applications.

IMPORTANT NOTE: The outer cooling jacket is not designed to withstand high pressure, so do not connect this to your house water pressure without the outlet of the chiller being open.


Average Rating:
(based on 8 reviews)

Showing 1 - 5 of 8 Reviews:

Review and Rate this Item
by Jack
on 4/5/2020
from NM
Was very impressed at how this little thing chilled my beer.
Wort came out at 68 deg. This was in March where the tap water is still pretty cool. I may have to do a ice bath as summer approaches. 
by terry vincent
on 12/7/2019
from Utah
First time
I used to wait hours for the wort to cool down to yeast pitching temp.  Today was the first time I every used any kind of chiller, 20 minutes after boil I was pitching yeast, so so happy with this product.
by Chris
on 3/18/2019
from Salinas
Great product at a great price
For 22 years I’ve used an immersion chiller and I’m blown away at how much more efficient and quicker this counterflow chiller is.
Wort leaves the kettle and enters this chiller at around 200-210 degrees Fahrenheit and leaves this chiller at 54 degrees. It takes around 15 minutes to gravity feed out of the brew pot through the ball valve. With the old immersion chiller I would usually loose patience after 20 minutes of chilling and dump the wort into the fermentor at around 80 degrees which is to warm. The cooling is painstakingly slow from 100 down to 70 with an immersion chiller but not with this counterflow ! It all happens in one pass through. 
by Gustave R.
on 4/3/2018
from Hicksville, NY
Good Chiller!
I was a little spoiled by my old 50' chiller as I had to slow down the wort flow through this 25' model to cool properly. Get the Q96 tubing kit and you'll be brewing immediately. Remember to sanitize before use and blow out the water if you're storing it in an unheated area in winter.
by Ken
on 1/24/2018
from TX
Counter flow review
First time I've ever used a counter flow, AWESOME!!! The flow thru thermometer showed 70 degrees into the keg. So much faster and easier than immersion chiller.
Review and Rate this Item
1/19/2020 10:38:39 AM
What is the inside diameter of the coil?
terry vincent
12/7/2019 3:39:59 PM
What would be the best way to drain this wort chiller and get all the moisture out to prevent any corrosion inside the tubing?
You ,don't have to worry about corrosion as the tubing is all copper. Just make sure to clean it right after brewing and blow out whatever water remains.
11/23/2019 4:00:27 PM
What is the easiest way to start a gravity flow siphon?
Either by sucking on the end to fill it, or to prefil it with water and then release the water with your thumb over the end when it is low enough.
9/9/2018 6:47:25 PM
Will the difference in hose ID cause major leaking problems if I connect to 1/2" Barb cam lock fittings to use with my pump?
It might, unless you can figure out a way to close the gap between 3/8 and 1/2"
Ask a Question

    Email A Friend

    Send this product to a friend...