• Intertap Self Closing Faucet Spring
  • This shows the spring with the L01 and L02 Intertap Shanks
  • This shows the spring installed in both Intertap Shanks

click on thumbnail to zoom
Item #: L30
Our Price: $1.99
Quantity:
 
In Stock, Will Ship On 05/28/2020.

Description 

This stainless spring converts an Intertap Faucet which is attached to an Intertap Shank to self closing. The wide end installs in the Intertap Shank, and the narrow end fits the Intertap Faucet inner seal, keeping it closed unless pressure is applied to the Intertap Faucet handle.

Works only with Intertap Faucets when installed on Intertap Shanks. When installing this in a Intertap Faucet/Intertap Shank pair, you may need to loosen the bonnet nut a bit on the Intertap Faucet to free it so will move back and forth easily.

Important note: This works with all Intertap Faucets except their Flow Control model. This does not work with any Keg Faucets, only faucets mounted on Intertap brand shanks.

Reviews

Average Rating:
(based on 12 reviews)

Showing 1 - 5 of 12 Reviews:

Review and Rate this Item
RatingReviewerReview
by Mike Ultee
on 1/26/2020
from New Jersey
No Intertap Faucet Should Be Without This Spring!
My wife bought me a 3-tap Kegerator a couple of years ago from Williams as a wonderful Christmas present. But neither of us knew about these springs. They push a faucet that is pulled forward to the open or flow position back to the closed position. Without the spring one may accidentally bump or tap one of the faucets causing beer to flow until the keg is exhausted. That can be a lot of beer lost to the floor and worse into carpeting! After two such accidents, a fellow home brewer told me about these springs. They install easily and work perfectly. Get them if you have Intertap faucets!
by Bill King
on 10/28/2019
from TX
Very nice tap
Everything you need to set up a tap on your keizer. Easy install, forward sealing taps never stick. 
by Marty
on 3/15/2019
from Michigan
Intertap self closing spring
Works like it should!
Well worth getting the Intertap shaft!
by Chuck
on 12/14/2018
from Gig Harbor, WA
Works for my Perlick 525
The spring is 2 1/2 inches long, which looked like it would be too long to work in my older Perlick 525 faucet.  However, in order to work the spring needs to be compressed, and this actually worked well.  It stopped the very slow drip that I had. It took a couple minutes to kind of jam it on, and then thread the faucet.  It's a two-hand operation, that would be easier with two people.  
by Dave
on 12/11/2017
from Las Vegas
SELF CLOSING FAUCET SPRING
I bought these springs even though I do not have the Intertap shanks. I figured at less than two buck each, what's the loss. They were, of course, too long. However with a little cutting (about 1/2 - 3/4 of an inch) with a grinding wheel, they fit and work just fine.  Would I buy them again, absolutely.
123
Review and Rate this Item

Other Items In This Category

QuestionAnswer
Greg
10/26/2019 1:58:53 PM
Is there a spring made for the flow control faucets?
No.
Bill
10/12/2019 3:02:54 PM
How long is this spring? I have a shallow chamber in a 4" Krome shank. Needs to be 5/8 to 3/4" long.
It is 2 3/4" long
Mike
7/13/2017 10:38:14 AM
Does this work with your Q79 faucet adapter?
No, only with Intertap Shanks
Scott
4/17/2017 3:35:17 PM
has anyone tried these with the Intertap Faucet and a different companies shank?
Yes, and they do not work.  The intertap shanks have a large shallow concave area to fit the spring and other shanks do not.
Ask a Question

    Email A Friend

    Send this product to a friend...