Paintball 0-30 PSI Brewer's Edge® Mini Regulator

  • Item #D70
  • Price: $69.99
  • Part #
- +
Share |

Take your beer with you when you go to the beach, camping, a game, or to a party. Our Paintball Tank Mini Regulator fits any standard C02 paintball tank (sold and refilled at sporting goods stores) without the need for adapters.

The system is built around a 0-30 psi C02 regulator that features precise adjustment via the calibrated top adjustment knob. It features a stainless steel check valve on the outlet ¼" threaded flare fitting, to prevent beer from backing out of the keg and into the regulator.

The flared outlet on the side can be attached to any threaded female ¼" flare fittings, such as our D03 Gas Connector. Change it into a ¼" hose barb if desired by ordering our D66 Barbed Adapter. The regulator is 3 1/8" tall when not attached to a Paintball tank.

The regulator does not include a needed C02 paintball tank. These can be purchased at many large box retailers and sporting goods stores, and can also be filled and refilled at these stores inexpensively. They generally come in sizes ranging from 12 ounce to 24 ounce, with 20 ounces being the most popular.


(11)
Average rating 9.27272727272727 out of 10 ( based on 11 reviews )

Awesome regulator!

Review by Steve on 6/30/2015

I use this to force carb and to bring my kegs with me to parties and my pool inside a portable kegerator. Where I live it's cheaper per pound to fill the paintball tanks than my 5 lb tank. This thing is tiny and works great! I love how it self vents when you dial back the pressure! I've always wanted one, but couldn't justify $120 for it, $60 i can justify!

Excellent

Review by Caleb on 7/6/2015

Finally an affordable paintball regulator. Works great to force carb. Excellent for my 2.5 gallon kegs and small kegerator! Super easy to use.

GREAT value

Review by Jon on 7/28/2015

I too use this to force carb and it works great. Can't beat the price. I will probably buy a second one for my mini 1.75 gal kegerator.

Good, but missing bracket

Review by Edwin on 10/6/2015

This is a solid mini regulator that should last for years. Unfortunately, Williams has chosen to sell this regulator without the hanging bracket that was included with the previous model that Williams sold. The bracket is very important because, as the included instructions explain, liquid CO2 could enter the keg and rupture it if the paintball tank and regulator aren't kept vertical. Williams doesn't even sell a bracket and the only online source I could find charges $25 with shipping for the bracket.

Mini regulator

Review by Carl on 10/12/2015

While not as precise as a Leland mini regulator which it resembles. It's adequate. My only complaint is it doesn't always hold the pressure that it's set at consistantly. Still a bargain at half the cost of the Leland.

Write a Review

Sep 24, 2018 by Jay

Q: Have had this product awhile, used little, recently dig up and think It had hard washer type gasket, am I correct and if so how are replacements acquired? Thanks

A: This regulator does not have a washer to seal the paint ball tank. It relies on the O ring on the lip of the paint ball tank valve which seals when it is screwed down. This regulator does have a burst disk, which is a emergency pressure relief valve under the 1.8K marked nut on the back center.


Nov 05, 2017 by Don Myers

Q: I have been using my paintball tank mini regulator to push beer from 3 gal. Kegs by placing this setup inside the cooler the kegs are in. I experience pressure drops and suspect the regulator freezes up. Do you think this is what is happening?

A: This depends on how many kegs, and how much gas is flowing. If you have multiple kegs, and you are pouring a beer every 5 minutes or so, the regulator will ice up. You could try mounting the regulator outside the refrigerator, and seeing if the problem goes away.


Jul 07, 2017 by Joe

Q: Will this regulator leak co2 slowly to regulate pressure? I plan to leave this hooked up for days at a time and do not want it leaking co2 when in idle.

A: No, if your keg has no leaks, and you set it for a steady dispensing pressure, it will not release C02.


Jun 02, 2017 by Gil

Q: Can this be used for pressure transfers? I plan on using this to carbonate my 2.5 kegs and do pressure transfers. Need something to be easily adjusted to 2 psi

A: 2 PSI is under the range that this regulator is comfortable with. So no, for 2 PSI transfers, this is not ideal.


May 10, 2017 by Matt

Q: can I get this with the female check valve instead of the male?

A: No, the regulator only comes with the male fitting attached. If you need the female fitting you can order item L10 and swap it out with the male fitting that comes on the regulator. Be sure to use some pipe thread compound on the threads before installation to prevent leaking.


Ask a Question